Plastic frame anchor W-UR F 6 SymCon®
Plastic frame anchor W-UR 6 SymCon pan head
ANC-(W-URSYM)-PLA-PANHD-AW20-A2K-10-6X60
ZEBRA
Register now and access more than 125,000 products
- SymCon screw: The dimensions of the anchor screw enable safe subsequent expansion properties
- SymCon screw: Screwing in the SymCon screw ensures optimum compression of the wall plug body plastic (virtually no undercutting)
- Improved load transfer: Even, continuous load distribution across the entire expansion area
- The hammer-in stop prevents premature expansion of the anchor during installation
- Pre-assembled wall plug body and special screw — easier installation
- Anchorage via friction locking between wall plug body and anchoring base
- Wall plug body made of high-quality polyamide
W-UR 6 SymCon and W-UR F 6 SymCon (galvanised steel): European Technical Approval ETA-11/0309
Drill cuttings must be removed from the drill hole.
Create the drill hole
Clean the drill hole
Set anchor and screw
Screw in the screw
Screw in screw until flush
W-UR 6 SymCon and W-UR F 6 SymCon (galvanised steel): European Technical Approval ETA-11/0309
Datasheets(X)
The anchor may be used with a European technical approval for the multiple attachment of non-load-bearing systems (e.g. suspended ceilings etc.)
Anchoring base with approval: Standard concrete ≥ C12/15
Unapproved anchoring bases: Solid brick, solid sand-lime brick, vertically perforated brick, hollow sand-lime brick, hollow lightweight concrete blocks, solid bricks and blocks made of lightweight concrete
Installation temperatures: Temperature of anchoring base: ≥–20°C, temperature of wall plug body: ≥ 0°C
Suitable for attaching ceiling substructures (made of wood or steel), wooden laths, metal rails, suspended ceilings, cable conduits, angle brackets, profiles etc.
Anchor diameter | 6 mm |
Anchor length (l) | 60 mm |
Nominal drill-bit diameter (d 0) | 6 mm |
Through-hole in the component to be connected (d f) | 6.5 mm |
Fire resistance rating | F30 |
Material of screw | Steel |
Internal drive | AW20 |
Surface of the screw | Zinc plated |
Head type | Pan head |
Drill hole depth (h 1) | 60 mm |
Approval | ETA-11/0309 |
Type description | W-UR F 6 SymCon, pan head screw |
| Performance data: Concrete, multiple attachment of non-load-bearing systems | |||
| Anchor diameter | [mm] | W-UR 6 SymCon | |
| Setting depth of the wall plug body | hnom [mm] | 50 | |
| Central tensile load1) for single anchors or dowel group | Nperm = C12/15 [kN] | 30°C2)/50°C3) | 0,79 |
| Nperm ≥ C16/20 [kN] | 30°C2)/50°C3) | 0,79 | |
| Shear load1) for single anchors or dowel group | Vperm | [kN] | 2,05 |
| Minimum component thickness | hmin | [mm] | 90 |
| Minimum axis distance4) | smin [mm] | C12/15 | 60 |
| ≥ C16/20 | 40 | ||
| Minimum edge spacing4) | cmin [mm] | C12/15 | 60 |
| ≥ C16/20 | 40 | ||
| Characteristic edge spacing | ccr,N [mm] | C12/15 | 60 |
| ≥ C16/20 | 40 | ||
| 1) The partial safety coefficients of the resistances as well as a partial safety coefficient of the effects of γF = 1.4 regulated in the approval are taken into account. For the combination of tensile and transverse loads, please refer to ETAG 020 Appendix C. 2) Maximum long-term temperature. 3) Maximum short-term temperature. 4) The permissible load must be reduced. | |||
| Installation parameters: Concrete | ||
| Anchor diameter [mm] | W-UR 6 SymCon | |
| Nominal drill diameter | d0 [mm] | 6 |
| Drill cutting dia. | dcut ≤ [mm] | 6,4 |
| Drill hole depth | h1 ≥ [mm] | 60 |
| Setting depth of the wall plug body | hnom [mm] | 50 |
| Through hole in attachment part | df ≤ [mm] | 6,5 |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!